Autor: Mic
hi from France thank you for this tool , it saved me many times, the reset program via the serial port is a must
View ArticleAutor: fjdejonge36@gmail.com
Hello Alnoor, I am interested in 1 of them. But what is the price for it. Please let me now. Many thanks. Frans
View ArticleAutor: maciej_333
I tested it with ATTINY2313 and ATTINY4313. Everything works good so 4313 should be change to green on list of supported devices.
View ArticleClik here to view.
Autor: qba
Miałem problemy z uruchomieniem układu, sygnatury były 01 02 03 jak z faq, układ przez rs232 zgłaszał wszystkie etapy ale nic się nie naprawiało. Sprawdzałem pod mikroskopem połączenia i luty, wszystko...
View ArticleAutor: Manicbomb
Hi, first awesome work dude! thi is a mad project! Can you please make a guide how to connect the lcd to it as you have on the Picture? Thanks
View ArticleAutor: Jakub
Cześć. Mam ATmega8 prawdopodobnie z uszkodzoną sygnaturą – AVRdude zawiesił się w trakcie programowania i klops. :( Fusebit Doctor (którego z powodzeniem stosuję już od roku) w wersji sprzed...
View ArticleAutor: Jakub
Już sobie poradziłem. Układ miał wyzerowaną sygnaturę oraz fusebity, a stan wysoki na pinie TX wymusił port RS232 komputera. Dziękuję za czas, który poświęciłeś na opracowanie i upublicznienie Doctora :)
View ArticleClik here to view.
Autor: Russell
My finished fusebit doctor. If helpful, I used ksp2222-NPN and PN2907A-PNP transistors, and Atmega 328P-PU Doctor chip. For resistor R7 to R23, used 470 ohm. Also used 470 ohm for R25 instead of 100...
View ArticleClik here to view.
Autor: Russell
Terminal window from Attiny 2313. Just remember, if fusebit doctor is powered without patient chip, circuit will hang in initial programming, Just install patient and push start. If powered up with a...
View ArticleAutor: Emanuel
hi i got 2 questions i was looking on pcb eagle after i removed the words to see whats done i notice there is 2 or 3 tracks that are not completed are they like that? also the atmega8 that then u will...
View ArticleClik here to view.
Autor: Russell
Push RATSNEST button and ground plane will fill in missing ground traces. You can use Atmega 328, just need to burn fuses to L-62, H-D1, E- FF or 07 depending on programmer. Need to use correct .hex or...
View ArticleAutor: Emanuel
awsome just seen it,im very new to this so sorry my question hehe yes ratsnake have field the ground traces, i see also the firmware for the 328p a bin file and a hex, how do i then set up the bin and...
View ArticleAutor: Russell
You will need a programmer to flash the Atmega chip, there are numerous types available. I often use USBTINY 2313 programmer in conjunction with AVRDUDE in a command line. Spark fun has pocket...
View ArticleAutor: Emanuel
thanks alot Russel for the info i will look into it, for what i understand i will need to use avrdude burn the fuses and flash the hex file into it, maybe i can use arduino has a isp or use a usBasp to...
View ArticleAutor: crazy4volvo
I just fixed a Arduino Mega R3 (Atmega2560-16AU) clone – some black magic has to be used (maybe 1k resistors are too much?) and some soldering work was needed, but finally fusebit doctor fixed it!...
View ArticleAutor: peter morgan
Do you sell completed boards for attiny 2313 repair and if yes how much are they and how to buy
View ArticleClik here to view.
Autor: kulamario
Witam Zbudowałem tego doktora ale jest problem bo nie działa poprawnie tz odblokowałem 5 z 9 prockow ale te diody nie świecą tak jak powinny tz wygląda to tak od pale doktora bez procka do leczenia...
View Article