Autor: manekinen
Ten kondensator jest tam dodany profilaktycznie, urządzenie powinno działać bez niego. Ale możesz wlutować dowolny inny, jednak nie większy jak 100nF (czas narastania i opadania napięcia).
View ArticleAutor: Patryk
Witam Zbudowałem twój układ i wystąpił mały problem . Kupiłem nową atmege8 , zaprogramowałem i w stanie bezczynności świeci czerwona dioda , wiec wsadziłem starego zablokowanego atmege 8 i po...
View ArticleAutor: Patryk
zrobiłem testowo adapter pod Attiny13 i go jakos udało sie naprawic lecz podlanczajac attiny2313 lub mega8 dalej czerwone
View ArticleAutor: Patryk
A wiec dalej sprawdzałem czy nie ma gdzies przerw w obwodzie i czy nie sa gdzies zimne luty lecz wszystko jest w 100 % porządku , podłączałem nawet sprawne atmega8 i 16 lecz dalej czerwone , tylko i...
View ArticleAutor: Patryk
Jednak pomoc juz jest zbędna , znalazlem problem okazało się ze jeden pin podstawki doktora byl pekniety i nie bylo pelnego styku a jeden nowy rezystor 1Kohm byl fabrycznie uszkodzony (brak przejscia)...
View ArticleAutor: manekinen
Patryku, pomoc ode mnie nadchodzi zwykle tylko w weekendy, w tygodniu nie zaglądam w komentarze. Ale i tak bym napisał abyś po raz kolejny sprawdził płytkę :)
View ArticleAutor: aXa
Hi, i am a newbie in programming AVR. And surely i have had 3 of my atmega1284p as dead because of chosing wrong fuse options. And nowadays i established your doctor circuit on a protoboard twice with...
View ArticleAutor: Bernhard Nebel
Hi manekinen, it turns out that the 2.11 firmware is unable to recognize the ATmega328 (or other chips from the ATmega8 family), once the DWEN or the RSTDISBL fuse has been activated. I wrote an...
View ArticleAutor: Bernhard Nebel
It seems that the odd behaviour was not caused by a bug in manekinen’s firmware, but by a hardware error (that apparently my firmware was able to get around): There was a connection between R25 and...
View ArticleAutor: serge
Hi, aXa pisze! I have made the same trouble. 2 mcu was locked! Please send me a scheme to repaire 1284p, please.
View ArticleAutor: Uniks
Witam, super projekt, właśnie złożyłem i wskrzesiłem zmartwych moją attiny2313. Jeszcze raz gratulacje dla Autora :-)
View ArticleAutor: aXa
Hi, i practicaly set the circuit defined by this site. Neither i used any other different scheme nor i provided myself a new circuit. Directly, i used the last version scheme of manekinen on a...
View ArticleAutor: andrew2222
Hello Manekinen, i have build the AVR doctor.Thank you for sharing this project with us. It seems i have a problem with LEDs sequence. When i try to reset a new/good ATmega8 (pacient) the two LED’s are...
View ArticleAutor: manekinen
Yes this should not happen. Can you check the info on the UART output?
View ArticleAutor: Russell
Hi Manekinen, Thank you for this splendid circuit bro. There is a prototype image using a linked HD44780 LCD display. Is there a circuit version/code for this available? Thanks for sharing all the...
View ArticleAutor: mcu
HI, if patient chip not recognized. like if we enter the hex signature. that means it CANNOT repair. right? thanks
View ArticleAutor: Michał
Cześć, zbudowałem powyższy układ "na pająka" bez RS-232 oraz z podstawką pod procesory 28-pinowe i zadziałał on "od pierwszego razu". Jeżeli komuś coś nie działa to należy bardzo dokładnie po kilka...
View ArticleAutor: manekinen
Does fuse doctor work ok with other known good patient? If yes, and if you entered signature bytes by hand and still nothing, then you can be pretty sure that this one is dead.
View Article