Autor: manekinen
Hello. Download #11 update, pcbs and schematics for adapters are in the „adapters” folder. HVSP adapter recognition is made by detecting connection from XTAL1 to OE (see hvsp adapter schematic).
View ArticleAutor: Jace\k
Witam. Zbudowałem układ w najnowszej wersji na uniwersalnej płytce drukowanej i mam dziwny problem. Gdy w podstawkę 40 pin włożę ATmega16A wszystko działa prawidłowo, zapala się zielona dioda. Kiedy...
View ArticleAutor: manekinen
Najprawdopodobniej to trup. Możesz jeszcze sprawdzić co sie pokazuje w terminalu, ale podejrzewam że nawet nie wchodzi w tryb programowania.
View ArticleAutor: Jacek
Powiem Tobie, że.. ATmega644PA działa! Wiesz, jak to zrobiłem? :) Już praktycznie nie dając sobie nadziei na jej działanie: wziąłem kawałek kabla, jedną końcówkę podłączyłem do 5V na płytce, a drugą...
View ArticleAutor: manekinen
<blockquote>wziąłem kawałek kabla, jedną końcówkę podłączyłem do 5V na płytce, a drugą zwarłem z wyjściem TxD mojej ATmega644. Po opisie układu doszedłem do wniosku, że to może tak...
View ArticleAutor: Maciej
Witam!! W całym tym układzie brakuje mi tylko jednego , w trybie manualnym powinien być jeszcze jeden punkt w którym możemy sobie znienić sygnaturę procka mimo że układ odczyta sygnaturę, spotkałem się...
View ArticleAutor: Michał
Znalazłem błąd. Po podłączeniu AtMegi8 układ zaprogramował na 2MHz, a nie na 1MHz, jak powinno być fabrycznie.
View ArticleAutor: manekinen
Sygnatury nie da się zmieniać. Czasem zostaje ona zmieniona na wskutek jakiegoś błędu, taka przypadłość avr.
View ArticleAutor: manekinen
Nie nie, układ ustawia E1 D9 co oznacza 1MHz. Jeśli wskakuje co innego to szukaj błędu w innym miejscu.
View ArticleAutor: Michał
Zwracam honor. Do grupy AtMeg8 wpadła mi jedna AtMega88 i akurat ją wziąłem do przetestowania. Układ działa tak jak trzeba :)
View ArticleAutor: Yuri
Hi I’m getting Received “Init programming…” and nothing more (without patient). Even if I’m taking chip (Atmega328) out of the doctor and just trying to power it – result is the same. stuck on „Init...
View ArticleAutor: manekinen
I think i don’t understand what are you trying to do. Run the circuit without a patient chip? Why?
View ArticleAutor: Russell
I had the same result as you did. The posted video here, shows a no chip condition posted on the terminal. Apparently older versions of the firmware worked this way. The newer 2.1X terminal UPDATE...
View ArticleAutor: Yuri
manekinen, I’m trying to troubleshoot the board, so I’m powering the chip outside of a board and expect to get „No chip in socket” result, but it’s not happening. It’s stuck on „Init programming…” Is...
View ArticleAutor: manekinen
No, you wont get it. The behaviour is good, it waits for respond from patient, there is no timeout for this (but yes i should implement some timeout). Powering it without a patient is pretty pointless.
View ArticleAutor: Russell
I understand your thought; why power without a patient, but I sometimes do that myself. Circuit wise, would it be feasible to add say, a 10K pull down to ground on RDY pin, or even to vdd. That way at...
View ArticleAutor: manekinen
Well, you can add this pulldown resistor if you want (avr dont have internal pulldowns). But this wont solve the lack of „no chip” message, it will still wait for RDY signal. I think i can add a 1...
View ArticleAutor: Russell
The „no chip” is really nice, but I would rather the circuit not hang in initial programming, looking for a chip that is not present. Like Yuri mentioned, +5 stays high until the RDY is found. It’s an...
View ArticleAutor: sorena
hello I have a mega32 with a problem. when i press the botton LED is going to turn off .whats the problem?
View ArticleAutor: manekinen
„no chip” + release the voltages, both of them, because 12V is also present.
View Article