Autor: szpila
Witam, rozważam budowę w/w układu i chciałbym się doradzić czy jest sens. Uszkodziły mi się (jeszcze nie wiem od czego i jak) dwa uP Atmegi8 niezależnie czy programuję je usbasp czy stk500(klon...
View ArticleAutor: manekinen
Błąd weryfikacji występuje pod różnymi losowymi adresami? Jeśli tak to tasiemka łącząca jest za długa (max 15cm), zasilanie kiepskiej jakości, nie zblokowane kondensatorkami 100nF. Może jakieś zimne...
View ArticleAutor: szpila
Na płytce już wcześniej programowałem kilkanaście razy procesor i było zawsze ok. Procesor nie był nowy gdy odmówił posłuszeństwa pomyślałem że porostu padł z zbyt dużej ilości programowania i kupiłem...
View ArticleAutor: Grzegorz
Genialny projekt.Stworzyłem układ na płytce uniwersalnej.Trochę się zmartwiłem gdy układ bez żadnego pacjenta nie pracował poprawnie.To jest przestroga dla takich amatorów jak ja.Chciałem po prostu...
View ArticleAutor: FULDA
Hi, In my shop they have only ATMega8A and not ATMega8. Is it problem? Or can I use 8A without problems? Thank you.
View ArticleAutor: AlxDroidDev
How do I program the Atmega8 wiwth the HEX file? I have both an Arduino and a cheap Chinese clone of a USBasp. Can I use either one of these to program the Atmega8 ? If so, how do I connect the Atmega8...
View ArticleAutor: Fernando
Dear, I fix atmega48 fine. but i have one atmega168-20pu the Reset disabled, but fuse doctor only show this: ***************************** AUTOMATIC HVSP MODE Init programming... DONE Read signature......
View ArticleAutor: Fernando
Men, i do one test with attiny2313, fc lock fix, but i disabled reset fuse also, same problem. I make rs232 to see, manual mode: MANUAL HVSP MODE Init programming... DONE Read signature... 36 36 36 -...
View ArticleAutor: manekinen
Hello, Atmega 48 and 168 are the same chip, the second one only have more memory, so both should work fine with doctor. And both were tested with it. Attiny2313 also was tested. When it’s freezing, it...
View ArticleAutor: manekinen
Mate, you have to use ISP connector to do this, there are tons of info around the web on how to do this :)
View ArticleAutor: Fernando
You are right! I remount and work fine now. Its a very useful project. Cheers!
View ArticleAutor: Radu
Hi manekinen, I built this to repair one Atmega328 that got wrong fuses because of some usbasp complications. I built it and it worked the first time, so I was able to repair my 328p successfully....
View ArticleAutor: Stan
Hallo Manekinen, i look for print-layout for fuse doctor. Is any chance? No problem PayPal or $/Eu pay. Thanks for any information. Stan, Brno, CZ
View ArticleAutor: MIREK
Ahoj Manekinko. Ten doktor absolutně nefunguje. Dělá si to co chce, jen ne to co by měl. Při osazení jakoukoliv atmegou, po stisku tlačítka červená led zhasne a pak se už nic neděje. Testováno na...
View ArticleAutor: Steve
Hi, great project & thank you for releasing it. I have just built mine & worked like a charm. I am interesting in using Bascom with Atmel chips, would it be possible to see the source code for...
View ArticleAutor: Jack Ravenno
Cześć! Dzięki! Bardzo fajne urządzonko. Zmontowałem jako wprawkę przed poważniejszymi projektami. Miałem mały problem z brakiem 12V na układach jednak szybko znalazłem przerwaną z jakiegoś powodu...
View ArticleAutor: Jack Ravenno
Hi! At first you MUST verify carefully that PCB is perfectly „error free”. I’ve had ONE error – simple broken track and my console screen was like yours. Init programming… and nothing more :/ Now my...
View Article