Autor: ghostknight
red led is ON … when push start button >>> red led OFF , wait few seconds ,green led flashing , and red led return ON … AND chip still not repaired can any one help please :)
View ArticleAutor: Harm
Hi there, Are there ready-made pcb’s (factory-made) for this project available? At dangerous-prototypes there are all out of stock and don’t sell/have them anymore. Please eply? Regards, Harm
View ArticleAutor: Rupert
Hi Manekinen I just wondered if you could help me with the correct fuses to burn your firmware on a 328P-PU for the Fuse Doctor chip, I am using AVRDUDESS as it supports the 328P and Arduino as ISP out...
View ArticleAutor: manekinen
Hi. Fuses are described in the readme file in the attachment. For M328: L:0×62 H:0xD1 E:0xFF And of course use proper firmware for this chip.
View ArticleAutor: Mahmoud
hello Manekinen i am going out right now to buy the components for this circuit but can you please tell me the difference between connecting the dead Atmega8 in the dip socket within the board and...
View ArticleAutor: Mahmoud
so this means that for example for Atmega8 & Atmega32 & Atmega16 i need no adapters to revive them ???
View ArticleAutor: manekinen
Nope, just put them into the main board. There are 3 sockets for most popular AVRs :)
View ArticleAutor: Live sex and chat cams
Hi, I think your website might be having browser compatibility issues. When I look at your blog site in Firefox, it looks fine but when opening in Internet Explorer, it has some overlapping. I just...
View ArticleAutor: Vladimir
Can I omit all 1k resistors ? I want to set up this schematic on a breadboard. That’s why I want to omit some parts (1k resistors).
View ArticleAutor: tomek
mam problem z atmega16.w pony prog wyskakuje mi Alert:dewice missing or unknown device (-24).wyswietlaja sie tylko czarne kwadraciki.stalo sie to gdy probowalem wpisywac rozne kombinacje fusebitow...
View ArticleAutor: manekinen
Yes you can, but if something will go wrong you will get hi-low state collision and can broke your uc’s pins.
View ArticleAutor: manekinen
Wywal tego pony proga i zacznij używać normalnego programu, np AVR Burn-O-Mat, wtedy nic nie zablokujesz. Co do problemu to ciężko powiedzieć, spróbuj podłączyć jakiś sygnał zegarowy na pin xtal1...
View ArticleAutor: tomek
Czy ktos juz robi odplatnie plytki do doktorka? Stk200,ponyprog i uklad atmega16 w ukladzie avt5229,probowalem wpisywac rozne kombinacje fusebitow do kwarca16mhz zewnetrznego,nawet z programu...
View ArticleAutor: tomek
OJ teraz zobaczylem,ze kolega Manekin odpisal.program Avr8 Burn-O-Matv2 tez mam ale cos Stk200 nie widzial,chyba cos zle kombinowalem. 1.O jakies czestotliwosci ma byc ten generatorek:1Mhz ? 2.posiadam...
View ArticleAutor: Rohit Soni
hello, It seems that i have a problem in reading and writng low fuse bits. the data on hyper termial is : MANUAL HVPP MODE Init programming… DONE Read signature… 1E 93 07 Searching chip… no names in...
View ArticleAutor: manekinen
Hello. You wont be able to change the fuses until you disable lockbits protection. First erase the chip (lockbits FF), then change fuses.
View ArticleAutor: korfanty
mam pytanie czy można udostępnić schemat tego fusebit doctor bez podstawek na leczone microkontrolery – tylko listwa z opisem pinów . Bo ja za bardzo nie połapię się w połączeniach „BUS” – ja tylko net...
View Article